? semiconductor components industries, llc, 2012 january, 2012 ? rev. 10 1 publication order number: mbrs1100t3/d mbrs1100t3g, SBRS81100T3G, mbrs190t3g, sbrs8190t3g preferred devices schottky power rectifier surface mount power package schottky power rectifiers employ the use of the schottky barrier principle in a large area metal-to-silicon power diode. state-of-the-art geometry features epitaxial construction with oxide passivation and metal overlay contact. ideally suited for low voltage, high frequency rectification, or as free wheeling and polarity protection diodes, in surface mount applications where compact size and weight are critical to the system. these state-of-the-art devices have the following features: features ? small compact surface mountable package with j-bend leads ? rectangular package for automated handling ? highly stable oxide passivated junction ? high blocking voltage ? 100 volts ? 175 ? c operating junction temperature ? guardring for stress protection ? aec ? q101 qualified and ppap capable ? sbrs8 prefix for automotive and other applications requiring unique site and control change requirements ? all packages are pb ? free* mechanical characteristics ? case: epoxy, molded ? weight: 95 mg (approximately) ? finish: all external surfaces corrosion resistant and terminal leads are readily solderable ? lead and mounting surface temperature for soldering purposes: 260 ? c max. for 10 seconds ? shipped in 12 mm tape and reel, 2,500 units per reel ? cathode polarity band *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. smb case 403a schottky barrier rectifier 1.0 ampere 90, 100 volts preferred devices are recommended choices for future use and best overall value. marking diagram http://onsemi.com b1 = device code x = c for mbrs1100t3 9 for mbrs190t3 a = assembly location y = year ww = work week =pb ? free package see detailed ordering and shipping information in the package dimensions section on p age 2 of this data sheet. ordering information ayww b1x (note: microdot may be in either location)
mbrs1100t3g, SBRS81100T3G, mbrs190t3g, sbrs8190t3g http://onsemi.com 2 maximum ratings rating symbol value unit peak repetitive reverse voltage working peak reverse voltage dc blocking voltage mbrs190t3 mbrs1100t3 v rrm v rwm v r 90 100 v average rectified forward current t l = 163 ? c t l = 148 ? c i f(av) 1.0 2.0 a non ? repetitive peak surge current (surge applied at rated load conditions halfwave, single phase, 60 hz) i fsm 50 a operating junction temperature (note 1) t j ? 65 to +175 ? c voltage rate of change dv/dt 10 v/ns stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. 1. the heat generated must be less than the thermal conductivity from junction ? to ? ambient: dp d /dt j < 1/r ja . thermal characteristics characteristic symbol value unit thermal resistance ? junction ? to ? lead (t l = 25 ? c) r jl 22 ? c/w electrical characteristics characteristic symbol value unit maximum instantaneous forward voltage (note 2) (i f = 1.0 a, t j = 25 ? c) v f 0.75 v maximum instantaneous reverse current (note 2) (rated dc voltage, tj = 25 ? c) (rated dc voltage, t j = 100 ? c) i r 0.5 5.0 ma 2. pulse test: pulse width = 300 s, duty cycle ? 2.0%. ordering information device marking package shipping ? mbrs1100t3g b1c smb (pb ? free) 2,500 tape & reel SBRS81100T3G b1c smb (pb ? free) 2,500 tape & reel mbrs190t3g b19 smb (pb ? free) 2,500 tape & reel sbrs8190t3g b19 smb (pb ? free) 2,500 tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
mbrs1100t3g, SBRS81100T3G, mbrs190t3g, sbrs8190t3g http://onsemi.com 3 typical electrical characteristics figure 1. typical forward voltage figure 2. typical reverse current* figure 3. power dissipation figure 4. current derating, case, per leg 20 10 5 2 1 0.5 0.2 0.1 0.05 0.02 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 v f , instantaneous voltage (volts) 100 ? c 25 ? c i , instantaneous forward current (amps) f 1 k 400 200 100 40 20 10 4 2 1 0.4 0.2 0.1 0.04 0.01 0.02 0 10 2030405060708090100 t j = 150 ? c 125 ? c 100 ? c v r , reverse voltage (volts) 3.2 2.8 2.4 2.0 1.6 1.2 0.8 0.4 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 t j = 100 ? c square wave dc i f(av) , average forward current (amps) p , average power dissipation (watts) f(av) 2.0 1.5 1.0 0.5 0 145 150 155 160 165 170 175 180 square wave dc t c , case temperature ( ? c) i , average forward current (amps) f(av) t j = 150 ? c i r , reverse current ( a) ? *the curves shown are typical for the highest voltage device in the voltage grouping. t ypical reverse current for lower voltage selections can be estimated from these curves if v r is sufficient below rated v r . 25 ? c figure 5. typical capacitance 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 0.1 0.2 0.5 1 2 5 10 20 50 100 v r , reverse voltage (volts) c, capacitance (pf) note: typical capacitance note: at 0 v = 270 pf
mbrs1100t3g, SBRS81100T3G, mbrs190t3g, sbrs8190t3g http://onsemi.com 4 package dimensions smb case 403a ? 03 issue h e b d c l1 l a a1 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. d dimension shall be measured within dimension p. 2.261 0.089 2.743 0.108 2.159 0.085 mm inches scale 8:1 *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* dim a min nom max min millimeters 1.90 2.20 2.28 0.075 inches a1 0.05 0.10 0.19 0.002 b 1.96 2.03 2.20 0.077 c 0.15 0.23 0.31 0.006 d 3.30 3.56 3.95 0.130 e 4.06 4.32 4.60 0.160 l 0.76 1.02 1.60 0.030 0.087 0.090 0.004 0.007 0.080 0.087 0.009 0.012 0.140 0.156 0.170 0.181 0.040 0.063 nom max 5.21 5.44 5.60 0.205 0.214 0.220 h e 0.51 ref 0.020 ref d l1 h e polarity indicator optional as needed on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 mbrs1100t3/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
